HSN code 7208 — FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH
HSN · heading18%हिंदी में देखें · தமிழில் பார்க்க
FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF 600 MM OR MORE, HOT-ROLLED, NOT CLAD, PLATED OR COATED
Hot-rolled flat steel sheets and coils that are at least 600 mm wide, made from iron or non-alloy steel, without any surface coating, plating, or cladding. These are raw steel products used in manufacturing and construction.
current gst rate
| igst | cgst | sgst | condition |
|---|---|---|---|
| 18% | 9% | 9% | Sch II S.No 267 |
source: 9/2025-Central Tax (Rate) · effective 2025-09-22 · all codes at 18%
gst calculator — pre-filled with this rate
products commonly classified here
black coilhot-rolled steel coilhot-rolled steel sheetHR coilHR sheetmild steel coilMS coil
more specific codes
- 720810IN COILS, NOT FURTHER WORKED THAN HOT-ROLLED, WITH PATTERNS IN RELIEF
- 720825OF A THICKNESS OF 4.75 MM OR MORE :
- 720826OF A THICKNESS OF 3 MM OR MORE BUT LESS THAN 4.75 MM :
- 720827OF A THICKNESS OF LESS THAN 3 MM :
- 720836OF A THICKNESS EXCEEDING 10 MM :
- 720837OF A THICKNESS OF 4.75 MM OR MORE BUT NOT EXCEEDING 10 MM :
- 720838OF A THICKNESS OF 3 MM OR MORE BUT LESS THAN 4.75 MM :
- 720839OF A THICKNESS OF LESS THAN 3 MM :
- 720840NOT IN COILS, NOT FURTHER WORKED THAN HOT-ROLLED, WITH PATTERNS IN RELIEF :
- 720851OF A THICKNESS EXCEEDING 10 MM :
- 720852OF A THICKNESS OF 4.75 MM OR MORE BUT NOT EXCEEDING 10 MM :
- 720853OF A THICKNESS OF 3 MM OR MORE BUT LESS THAN 4.75 MM :
- 720854OF A THICKNESS OF LESS THAN 3 MM :
- 720890OTHER
sibling codes
- 7201PIG IRON AND SPIEGELEISEN IN PIGS, BLOCKS OR OTHER PRIMARY FORMS
- 7202FERRO-ALLOYS
- 7203FERROUS PRODUCTS OBTAINED BY DIRECT REDUCTION OF IRON ORE AND OTHER SPONGY FERROUS PRODUCTS, IN
- 7204FERROUS WASTE AND SCRAP; REMELTING SCRAP INGOTS OF IRON OR STEEL
- 7205GRANULES AND POWDERS, OF PIG IRON, SPIEGELEISEN, IRON OR STEEL
- 7206IRON AND NON-ALLOY STEEL IN INGOTS OR OTHER PRIMARY FORMS (EXCLUDING IRON OF HEADING 7203)
- 7207SEMI-FINISHED PRODUCTS OF IRON OR NON-ALLOY STEEL
- 7209FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF 600 MM OR MORE, COLD- ROLLED (CO
- 7210FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF 600 MM OR MORE, CLAD, PLATED OR
- 7211FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF LESS THAN 600 MM, NOT CLAD, PLAT
- 7212FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF LESS THAN 600 MM, CLAD, PLATED O
- 7213BARS AND RODS, HOT-ROLLED, IN IRREGULARLY WOUND COILS, OF IRON OR NON-ALLOY STEEL
Not sure this is the right code? Try the guided finder →
compiled from official sources · not tax advice · verify with your tax advisor before filing